Heaven's Hell set of 5 - collar - bracelets - ankle bracelets

Stainless steel set consisting of 1 BDSM collar, 2 BDSM bracelets and 2 BDSM ankle bracelets - Heaven's Hell - lockable and with two keys

The BDSM bands from the Heaven's Hell series are the classic among stainless steel restraints. All straps are individually handcrafted and adjusted according to your dimensions. Equipped with a hinge in the back and a visible lock at the front. The stainless steel shackles can be supplemented with an O-ring. This is attached to a removable stainless steel holder.

The effect of our stainless steel bands can be felt simply by the weight of the material. Thanks to the precise craftsmanship, they also fit perfectly and are therefore suitable for longer periods of wear. Guaranteed captivating hours, no matter which end of the chain you are at.

Please note: If the bands are ordered without a ring, it cannot be attached later without us leaving the opening for it later!

Dimension guide

In order to create the stainless steel strips precisely, we need your individual and exact dimensions. For the measurement it makes sense to have two people. Please proceed as follows and enter the dimensions in centimeters and millimeters (cm, mm) in the field provided in the order listed below (1) / 2) / 3) or A) / B) / C) or I) / II) / III) ) to:

collar

1) SCOPE

Measure the neck circumference using a flexible tape measure. Keep your head straight while measuring and place the measuring tape at the level of the larynx. Please note this circumference value under 1).

2) DIAMETER WIDTH

For this you will need two hardcover books. Hold these with the spines of the books at the sides of your neck. Make sure that the books only touch the skin of the neck, but do not press it. Both books must be aligned parallel to each other. Now use a ruler to measure the distance between the two spines of the book. Alternatively, use a caliper. Write down the value under 2).

3) DIAMETER DEPTH

For this you will need two hardcover books. You hold these with their spines against your neck, both at the front and at the back. Make sure that the books only touch the neck, but do not dent it. It is important that the books are at the same height, namely at the thickest part of the neck (larynx). Both books must also be aligned parallel to each other again. Now use a ruler to measure the distance between the two spines of the book. Alternatively, use a caliper. Write down the value under 3).

bracelet

A) SCOPE

Measure the circumference of your wrist using a flexible tape measure. To do this, place the measuring tape smoothly behind the wrist bone without constricting it. Read the circumference in centimeters and millimeters (cm, mm). Enter the value under A).

B) WIDTH

Measure the width of your wrist using two books with solid spines. The measurement also takes place directly behind the wrist bone. To do this, place your forearm and hand flat. Bring the two books from the left and right with the book spines towards both sides of the arm so that the book spines touch the arm but do not press it in. Align the two spines parallel to each other and now use a ruler to measure the width of your forearm by measuring the gap between the spines. Alternatively, use a caliper. Specify this value under B).

C) HEIGHT

To determine the height of your wrist, place your forearm upright so that the edge of your hand rests on the surface. Bring two books with stiff spines to the top and bottom of your arms so that the spines touch the skin but do not press it. Align the two book spines parallel to each other and use a ruler to measure the width of your forearm by measuring the gap between the book spines. Alternatively, use a caliper. Please specify this value under C).

Ankle band

I) SCOPE

Measure the ankle circumference using a flexible tape measure. To do this, place the measuring tape smoothly on the leg directly above the ankle joint. From there, guide the band completely around the leg. Please note this circumference value under I).

II) WIDTH

You measure the width of the ankle bracelet using two books with a solid spine. Bring the two spines of the book to both sides of the leg (left and right) so that the spines touch the skin of the leg but do not press it. Align the two spines parallel to each other and now use a ruler to measure the width of your leg by measuring the gap between the spines. Alternatively, use a caliper. Please note this value under II).

III) DEPTH

To determine the depth of the ankle bracelet, place your foot on the floor. Bring two books with stiff spines to the front and back of the leg so that the spines touch the skin but do not press it. Align the two spines parallel to each other and use a ruler to measure the depth of your leg by measuring the gap between the spines. Alternatively, use a caliper. Please indicate this value under III).